The long tail cast on can also be done with 2 hands. Repeat steps 4-6 until you have casted on all the stitches you need to start your project. Step 6: Release the loop in the thumb under the needle. Step 5: In a clock wise motion without releasing the loop in the thumb, bring the needle over the strand in the index finger and drag it inside the loop of the thumb. In a counter clock wise motion, pass the needle under the strand on the left side of the thumb and drag it up. Step 4: Put the finger again in slingshot position. Press down and turn the needle clockwise, dragging the strand on the right of the thumb, and creating the first stitch in the needle. Step 3: Put the needle above the strand that goes from thumb to index finger. We commonly call it "slingshot position". Step 2: Hold both strands against your palm with the other fingers. Let the short tail hang over the thumb, taking care that it is long enough to cast on all the stitches (there are some tricks in this article). Step 1: Put the yarn over your thumb and index finger, that are open in a V position. In this tutorial we will show you a more direct way to start casting on stitches If it is the first time that you do the long tail cast on you can start with a slip knot. Is for that reason that in the instructions of most non circular patterns the first row starts with the wrong side row. This is going to save me so much time.Although long tail cast on is any cast on method that use 2 long strands of yarn to create the first stitches ( german twisted cast on, Channel Island, Estonian or Latvian cast on.), when we say long tail cast on we generally refer to this basic way of casting on stitches that we are going to see today.įor its way to work the stitches, the structure in the base of the fabric is like we have altready knitted a first right side row. I don’t know how many times I have had to start over with the casting on step because I didn’t have a long enough tail. This was VERY helpful! I am a long time knitter, but get frustrated with casting on over and over to get it right Replyīrilliant! I will be using this measuring tip on my next project. I like the long tail cast on, but I also really like Nancy Lingerfelt’s recommendation, and well be trying that one next. My personal recommendation is to wait until you have knit a few rows before cutting the yarn, in case there’s a problem and you have to frog and cast on again. when you are finished, decide which is to be the working yarn (inside or outside of skein) and cut the other yarn. You can also use both tails of the skein of yarn.tie them together, make a slip knot and proceed with long tail cast on. If I have reached it, I know I won’t have enough yarn, and need to start over with a longer tail. After I’ve reached the halfway point of casting on, if I haven’t reached that slip knot yet, I know I have enough yarn. Once I’ve decided how long the tail needs to be to cast on, I put a slip know in the middle of that tail. Δ 6 Responses to “Long Tail Cast On Hack” Mail (required) (will not be published).Tags: cast on, how to knit, long tail cast on, tips & tricks ![]() If you need a refresher on how to work the long tail cast on, check out our free video here.ĭo you have any tips for the long tail cast on you’d like to share? Let us know in the comments! From there, you can work the long tail cast on for the number of stitches you need. ![]() Once you have your yarn tail estimated, make a slip knot and place it on the needle-this counts as your first stitch. It’s always better to have a little extra yarn leftover in your yarn tail than to run out of yarn when casting on a lot of stitches. If you need to cast on a lot of stitches (for example 300 or more for a bottom-up shawl), I would suggest adding a little extra yarn into your tail as an extra insurance policy. Continue this process until you have estimated for the total number of stitches the cast on calls for. Fold it over again to represent 20 stitches, again for 30 stitches, and so on. Now that you have that length of yarn, you can fold the yarn over itself to estimate more stitches. ![]() That length of yarn is what you’ll need in your tail to cast on 10 stitches. Pinch the yarn at either end of the needle and unwrap it from the needle. Starting with the needles and yarn for your project, leave a tail of six to eight inches, then wrap the yarn around the needle 10 times. ![]() However, you can use this quick trick to estimate the length of your yarn tail so that you can be sure you have enough yarn to complete your cast on. There are a lot of factors that can affect the tail length, such as yarn composition or your gauge, just to name a few. The key to the long tail cast on is all in the name-you’ll need a long tail to start. For many knitters, it’s the first one they learn when starting their knitting journey. The long tail cast on is one of the most common cast ons used in knitting.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |